Sharing my build of the Cazador

Joined
Jan 15, 2018
Messages
16
Points
13

#21
Thank you for the advise on doing the pully blocks before doing anymore rigging. Even with the few lines I have completed already and can see there being a problem ahead in pinning the yards and pully blocks. I shall do these next before doing any further rigging. Kevin
 

Donnie

Well-Known Member
Blandford Group Build
Joined
Aug 21, 2011
Messages
2,138
Points
113

Location
Madison, MS
#24
I agree with Pat. The main thing here on SOS is to "enjoy" your hobby. I wish that I could build the perfect ship, but I make many mistakes and problems. Kits do not always supply the best info on rigging. I am glad that you chose SOS to display your work. Very nice workmanship !!!

I built the Santisima Trinidad from OcCre, and all of the Belaying pinouts were wrong. I had to do a lot of research to figure out the pattern of how things work. I am not against OcCre, maybe something in the translation - I am not sure. All I know is that the "belaying pin PLAN" was quite backwards as they had lines from the way AFT of the ship tieing to the fore yards and I knew that it could not be possible. I figured out that the Belaying pins tie off points were in direct relationship physically with each MAST. Each Mast section has its own belaying pin section if you will think of it this way.
If you care to, you can view my personal build log to see the way I perform the rigging.
http://shipsofscale.com/Trinidad/
(just as a reference of course)
 

kah4

Member
Joined
Jan 15, 2018
Messages
16
Points
13

#25
Back to building again..had a break as felt it was needed. Refreshed and ready to go. Currently completing the spars now with blocks and rigging. Thank you all for your comments of support. I agree, this is about enjoyment and that is why I felt a break was needed. I am enjoying this build but the rigging is certainly a challenge. Needed the break to look at this afresh. I will post further photos as I progress. Kev
 

paulv1958

Well-Known Member
Joined
Jul 7, 2015
Messages
442
Points
63

Location
Melb, Australia
#27
Rigging is the most brain consuming process known to man!. I would do only one or two lines a day. It's enjoyable watch it come too life, but needs eye & brain strain resting.
 

epicdoom

Well-Known Member
Staff member
Moderator
Blandford Group Build
Joined
Aug 4, 2018
Messages
736
Points
93

Location
Baltimore, Maryland USA
#28
for me the rigging is the climatic end to a build, I love rigging. I first started off looking for the most complicated, confusing, mind twisting mess of wood bits and thread I could find. the more thread I saw the better. yeah I'm one twisted old man I know, but I'm happiest in a build doing that rigging.
 
Joined
Jan 15, 2018
Messages
16
Points
13

#31
Fore mast now complete (I hope). Will check everything again later once all masts rigged. Definitely a good idea (as Paul suggested) to do the outer rigging once spars are in place and inner rigging completed. Much easier to rig that way. It s a deviation from the plans but well worth it. Just made sure I have marked on the plans the completed lines to save any confusion at a later stage (Hate to rig it twice).
 

Attachments

paulv1958

Well-Known Member
Joined
Jul 7, 2015
Messages
442
Points
63

Location
Melb, Australia
#33
nice work, looking great. It is the fiddliest rigging I have ever done. I think the fact its all running and all to the edge of the hull that makes it a challenge. Square rigs are more complex, but a lot easier to do.

A great job and a ship to be proud of.
 
Top