Glue

Bazzg

New Member
Joined
Sep 28, 2018
Messages
3
Points
3
#1
Hi all again just having a cuppa while hoping you can help with a Easy Peasy question for you at least, what type of glue do recommend for glueing my ship model, iv been advised Uhu, glue stick or Pva and sometimes glueing the card before putting the paper on instaed of the paper first,or putting onto spare paper then transferring using a pin onto paper. So i was going to buy some small brushes and spreaders iv seen on ebay and using Pva glue. Stuck before i even start i hear you say, just want to get it right before i argue with the paper or blame the Dog.
 

epicdoom

Well-Known Member
Joined
Aug 4, 2018
Messages
513
Points
93

Location
Baltimore, Maryland USA
#2
What type of model? wood, paper, plastic for wood POF I glue the templates to the wood with UHU Stic its a glue stick type this allows easy removal of the template after its cut out. for gluing the model together I use Titebond III or Elmers Glue All white glue depends on what and where I'm using the glue some things you want a clear glue and the Elmers White glue dries clear the titebond III however has a brownish look to it when dry. I also use CA specifically from BSA I use Thin and extra thick and I use the accelerator with that glue when needed. PVA glue I have found is a mixable type it comes in powder form and is mixed with water I do like it for patterns however it has a shelf life which is very short so its best to mix only what you need. hope this helps
 

zoly99sask

Well-Known Member
Staff member
Administrative
Moderator
Joined
Apr 13, 2015
Messages
2,017
Points
113

#3
I think Barry is asking about glues for paper/card models.
 

epicdoom

Well-Known Member
Joined
Aug 4, 2018
Messages
513
Points
93

Location
Baltimore, Maryland USA
#6
The carding you want depends on the thickness required in the plans for building the model so far looking at the plans you will want 1mm and .5 mm thick I found this on amazon for the 1mm stock its a tad over but should work fine https://www.amazon.com/gp/product/B076HVZZ8H/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
amazon should have stock that .5mm also but I haven't looked as I have a lot of that size from a paper company I go to for work they were nice to donate it to me because I fix there equipment often.
 

Donnie

Well-Known Member
Joined
Aug 21, 2011
Messages
2,094
Points
113

Location
Madison, MS
#7
It seems to me (and I am totally ignorant about the paper part), that it would depend on what part you are making as to what weight of paper you would use.? ! ?
f.e., a Mast might be made of heavier stock. Or I guess the mast could be rolled to make a tighter tube... I don't know. I better just be quiet and leave the paper to the guys that know what they are doing. ;)
As far as the glue goes, I did not know that there were so many types of glues until I went into my wife's hobby store where she works. There seems to be hundreds of ways and products to glue things. From glue sticks to glue guns.
 

epicdoom

Well-Known Member
Joined
Aug 4, 2018
Messages
513
Points
93

Location
Baltimore, Maryland USA
#8
It seems to me (and I am totally ignorant about the paper part), that it would depend on what part you are making as to what weight of paper you would use.? ! ?
f.e., a Mast might be made of heavier stock. Or I guess the mast could be rolled to make a tighter tube... I don't know. I better just be quiet and leave the paper to the guys that know what they are doing. ;)
As far as the glue goes, I did not know that there were so many types of glues until I went into my wife's hobby store where she works. There seems to be hundreds of ways and products to glue things. From glue sticks to glue guns.
the card stock size is written on the plans sheet to build the model so far looking at the plans I have the sizes are 1mm and .5mm for just about everything you have to follow the plan and use what size they say for each part some parts get no carding at all.

Your so right about Glue there are tons different brands of the same type but brand X swears they make better glue then Brand Y the whole deal makes my head hurt just thinking about it. The glues I use are from experience in using those types in the situation and those glues were all recommendations at one point from other folks. Knowing all the different glues out there this made choosing easier and I later found they did what I needed them to do so I never changes to something else. Any wood glue will work with paper after all paper is wood. so In essence wood glue will build the whole model made of paper. that said certain parts your gonna want to stiffen up some wood glues don't dry hard on every surface some dry flexible so wouldn't serve the purpose to stiffen the object that's where CA comes in. it just depends on the needs sometimes you want flexible some times you don't.
 

kay

Member
Joined
Sep 26, 2018
Messages
8
Points
13

Location
Germany
#9
Last edited by a moderator:

kay

Member
Joined
Sep 26, 2018
Messages
8
Points
13

Location
Germany
#11
Thank you. But the only wood I've used here are the masts and deck planking. The hull is made of cardboard and treated only in color.
To get on the glue again, I always take glue that is water free.

Regards Kay
 

epicdoom

Well-Known Member
Joined
Aug 4, 2018
Messages
513
Points
93

Location
Baltimore, Maryland USA
#12
WOW that's amazing for being cardboard. I have the shipyard Victory I have been collecting card stock in the proper thickness for the build but I'll probably mix wood into the kit as well. I did buy the sail and mast kits for it also so ill probably do the decks in wood. I bought the kit with the idea in mind to use all the patterns for an all wood ship build, but I have a Victory wood kit and though it might be nice to just build it in the stock its supposed to be in. The biggest issue for me with the kit is I hate to cut stuff out with scissors so I have done the frame and its parts with a straight edge and hobby knife even that gets to me after a bit so I enlisted the help of my wife. she is a scissor using fool and cuts the parts out super quick as well as accurately.
 
Top